Dopp Estate. Boats, wheeler, van, trailers, tools

Dopp Estate. Boats, wheeler, van, trailers, tools

Auction closed.
Auction closed.
Dopp Estate. Boats, wheeler, van, trailers, tools

Dopp Estate. Boats, wheeler, van, trailers, tools

Auction closed.
Auction closed.
Internet Premium: 9.5%
See Special Terms for additional fees
Share:

Description

Craftsman & other woodworking, mechanic equip & tools; Polaris wheeler w/ plow; Thompson 20' inboard boat, trailer; band mill project; electronic tools & scrap, some gold; '93 Chevy van; collectibles

Bennett Auction Service



(715) 657-0078
Need help with bidding? Get Help
Catalog Terms of sale
Search Catalog :
Sort By :
Go to Lot :
Go to Page :
Per Page :
Pg : 1 of 20

9 hp. Vertical / horizontal wood splitter, takes blocks up to 24" long

Lot # 135      

Splitter appears in good condition. Easily converts from horizontal to vertical by removing a bolt, uprighting the splitting assembly, and reinserting the bolt. Stored under roof and the engine was covered when we found it. Splitter cylinder is 5" OD and 28" long. 6" x 6" I-beam frame has 3/8" flanges. Splitter wedge is 7" tall. Splitting plate is 1-1/2" thick. Gas in tank smells old. Engine runs with a splash of gas in the intake, but will not keep running. Maybe a stuck float, maybe something else. Small tire on jack stand is cracked and goes flat. Comes with spare cylinder seals, axle caps, plug wrench, more.
...more

Bid Not Accepted!

Bid Accepted!

You've been outbid!

Sold for: USD 600.00

You've been outbid  to J****s! to YOU!

Placing your bid. please wait...

12' firewood trailer

Lot # 151      

Box is 12' x 6' x 2' d with removable stake sides, front and back. Tires are up and good enough, have some cracks. Comes with a spare. One side lens is cracked out on the tail lights. Appears to be a very sturdy trailer.
...more

Bid Not Accepted!

Bid Accepted!

You've been outbid!

Sold for: USD 500.00

You've been outbid  to j****e! to YOU!

Placing your bid. please wait...

18' trailer frame, maybe part of Jim's lumber mill project, see lot 325. Round bale trailer?

Lot # 150      

Straight portion of frame is approx. 18' x 4-1/2', tongue is an addition 5'. Frame has jacks at all four corners and a heavy steel carriage mounted on it, possibly for Jim's lumber mill project. Tires are holding air. No lights.
...more

Bid Not Accepted!

Bid Accepted!

You've been outbid!

Sold for: USD 170.00

You've been outbid  to J****b! to YOU!

Placing your bid. please wait...

Nice little single axle trailer with folding ramp, good for lawn mower or 4-wheeler

Lot # 152      

Trailer box is 6'6" x 4'. Fold down ramp is 4' long extended. One tire is flat, so plan accordingly. Comes with a spare that's also flat. Trailer is wired, but some of it's hanging loose. Nice little trailer
...more

Bid Not Accepted!

Bid Accepted!

You've been outbid!

Sold for: USD 90.00

You've been outbid  to n****t! to YOU!

Placing your bid. please wait...

2004 Polaris Sportsman 700 Twin with on demand AWD & Polaris 5' quick attach plow

Lot # 161      

4-wheeler with 1,525 miles starts, runs and drives. In good condition for age. Very good tires. Quick mount plow is raised and lowered by a Warn winch. Fenders and body are in good shape. Cargo racks have a few cracks and chips, but it doesn't affect function. One headlight lens is broken, the other is cracked. Thumb throttle is wrapped with black tape. Seat cover is in good shape. Battery seems weak, loses charge even when disconnected. Winch works. Comes with spare key, plug wrench, more. Registration expired June 2013.
...more

Bid Not Accepted!

Bid Accepted!

You've been outbid!

Sold for: USD 3,600.00

You've been outbid  to n****3! to YOU!

Placing your bid. please wait...

1968 Thompson Model GV-205 20' inboard boat & Karavan Classic tandem axle trailer

Lot # 157      

Boat is powered by a 283 Chevy V-8 engine. Fiberglass hull. Comes with two Riviera deep trollers, three props, life vests, side ladder, two questionable batteries, Solara CB, Eagle fish locator, Colormatic II depth finder, tools, rope, fuel stabilizer, more. Trailer was manufactured late 2003 and can carry a max load of 4800 lbs. GVWR/PNBV 5,780 lbs. GAWR/PNBE 5,780 lbs. Trailer has hydraulic brakes, tires still have molding stubs on them. Trailer is clean and in exceptionally nice condition. Boat was tarped in the side yard over winter. Bundled storm covers and boat interior were wet and are mildewy/musty. Needs a good cleaning. Last registration expired in 2013. Signed boat title in hand and ready to transfer. The boat had been restored, see Lot #154 for parts boat.
...more

Bid Not Accepted!

Bid Accepted!

You've been outbid!

Sold for: USD 1,400.00

You've been outbid  to A****0! to YOU!

Placing your bid. please wait...

1969 Thompson Model GV-205 20' inboard boat and tandem axle trailer

Lot # 154      

Powered by a V6, firing order 1 6 5 4 3 2. Distributor is on the front, mounted at about 45 degrees. Fiberglass hull. This was a parts boat for Lot #157 and does not have a title. Family is agreeable to work with buyer to register, if desired. Tires appear to be holding air. We don't know if this trailer is road worthy, so come prepared. Boat was last registered in 2009. Come to the open house and check it out.
...more

Bid Not Accepted!

Bid Accepted!

You've been outbid!

Sold for: USD 150.00

You've been outbid  to b****a! to YOU!

Placing your bid. please wait...

Nice aluminum receiver hitch utility rack

Lot # 156      

49" x 23". Mounting tube is 2" square. Plastic corners are aged, some are cracked - easily replaced.
...more

Bid Not Accepted!

Bid Accepted!

You've been outbid!

Sold for: USD 55.00

You've been outbid  to m****1! to YOU!

Placing your bid. please wait...

John Deere 10P utility dump trailer

Lot # 159      

Trailer measures 48"x43" across top. Pneumatic tires are decent. Box is molded with 6 stake pockets and channels for two load dividers. Very well made and in good condition.
...more

Bid Not Accepted!

Bid Accepted!

You've been outbid!

Sold for: USD 95.00

You've been outbid  to a****a! to YOU!

Placing your bid. please wait...

1993 Chevy G20 Family Wagon conversion van

Lot # 158      

Starts, runs and drives. Tires are good to very good - have a lot of tread, but some cracking. 128,270 miles. Oil looks fine. Windshield is cracked. Upholstery and carpeting are good with a few minor stains, some dog hair, and one 2" tear on left of driver seat. Registration expired May 2013. A/C may need work. Battery was zombie dead from sitting over winter, takes a charge but doesn't hold it more than a few days. Signed title in hand, ready to transfer.
...more

Bid Not Accepted!

Bid Accepted!

You've been outbid!

Sold for: USD 750.00

You've been outbid  to n****t! to YOU!

Placing your bid. please wait...

4' x 3' utility trailer with removable sides

Lot # 153      

Sprung axle. Tires appear good. Wood could use an upgrade or use as is (for a while).
...more

Bid Not Accepted!

Bid Accepted!

You've been outbid!

Sold for: USD 55.00

You've been outbid  to s****s! to YOU!

Placing your bid. please wait...

Delta ShopMaster 10" cast iron table saw with side wings, rip fence, miter gauge, guard, more

Lot # 589      

I'm impressed with the quality of this saw, it runs very smoothly and quietly, the stand is sturdy. Rip fence glides smoothly, locks up tight and adjusts out to 28". Throat plate is thicker and more rigid than some I've seen. Miter gauge slots are T-shaped so as to trap the front of the gauge and keep it from lifting. Miter gauge has three adjustable detent stops at 45, 90 and 45 degrees and pivots 60 degrees to each side. Side wings are stamped from heavier gauge steel. 4,000 rpm direct drive motor. Blade tilts 45 degrees to the right. Includes blade guard with anti-kickback dogs, arbor wrench, and an extension cord.
...more

Bid Not Accepted!

Bid Accepted!

You've been outbid!

Sold for: USD 240.00

You've been outbid  to b****w! to YOU!

Placing your bid. please wait...

Bid Not Accepted!

Bid Accepted!

You've been outbid!

Sold for: USD 11.00

You've been outbid  to T****1! to YOU!

Placing your bid. please wait...

Craftsman ball bearing router mounted under a Skil 15" router table; Craftsman router case

Lot # 591      

Router runs fine. Table is in good shape. Comes with a 1/2" straight bit and blow molded Craftsman router case.
...more

Bid Not Accepted!

Bid Accepted!

You've been outbid!

Sold for: USD 50.00

You've been outbid  to r****3! to YOU!

Placing your bid. please wait...

Rockwell 6" stacking dado kit, catalog number 34-334

Lot # 595      

Kit appears to stack to a little over 3/4". Blades are drilled with 5/8" arbor hole. Some 1/2" reducers are included. Two side blades and five center blades. Includes arbor flange.
...more

Bid Not Accepted!

Bid Accepted!

You've been outbid!

Sold for: USD 8.50

You've been outbid  to p****s! to YOU!

Placing your bid. please wait...

Avenger 7-1/4" adjustable carbide tipped dado head with 1" arbor hole

Lot # 594      

Appears unused. No arbor flange marks on the paper label. Infinitely adjustable from 1/8" to 3/4" dado width. Missing one carbide tip.
...more

Bid Not Accepted!

Bid Accepted!

You've been outbid!

Sold for: USD 1.00

You've been outbid  to m****b! to YOU!

Placing your bid. please wait...

Bid Not Accepted!

Bid Accepted!

You've been outbid!

Sold for: USD 12.00

You've been outbid  to a****a! to YOU!

Placing your bid. please wait...

Drill sharpener and multi-plug reel

Lot # 588      

Drill sharpener motor runs smooth and quiet. Switch is broken and does not shut off. Drill grinding attachment is adjustable and pivots smoothly. Multi-plug reel looks like it would be handy.
...more

Bid Not Accepted!

Bid Accepted!

You've been outbid!

Sold for: USD 11.00

You've been outbid  to H****3! to YOU!

Placing your bid. please wait...

Jet 12-1/2" deluxe planer Model # JWP-12DX

Lot # 587      

Infeed and outfeed tables have rollers. Planer head has 6" of vertical travel. On/off switch has a removable lock. Comes with an extra set of knives and misc. tooling/parts. One height adjustment lock is missing a handle. Infeed and outfeed tables fold up for easy storage and transport. Nice job site planer. Chip brush included.
...more

Bid Not Accepted!

Bid Accepted!

You've been outbid!

Sold for: USD 230.00

You've been outbid  to p****k! to YOU!

Placing your bid. please wait...

Craftsman 10" radial arm saw with sturdy stand and very nice laminate table

Lot # 584      

Radial arm assembly pivots 60 degrees to each side. Saw head has 16" of travel, tips over 90 degrees to one side and swivels 90 degrees for rip cuts. Angle iron stand is nice and sturdy. Generous 48" x 27" table appears to be marine grade plywood. Ball bearing motor runs smoothly. Comes with a carbide tipped saw blade. Very nice set up. Comes with a bonus tape measure.
...more

Bid Not Accepted!

Bid Accepted!

You've been outbid!

Sold for: USD 85.00

You've been outbid  to h****r! to YOU!

Placing your bid. please wait...

Delta/Rockwell 16" cast iron scroll saw with stand

Lot # 583      

11" x 11" table tilts 45 degrees to each side. Saw runs fine. Stand is wobbly and needs bracing.
...more

Bid Not Accepted!

Bid Accepted!

You've been outbid!

Sold for: USD 55.00

You've been outbid  to 3****a! to YOU!

Placing your bid. please wait...

Craftsman 18" cast iron scroll saw frame

Lot # 582      

Nice sturdy cast iron frame and table are in good condition. Table measures 12"x12" and is missing throat plate. Pulley and drive arbor rotate freely and smoothly. Bottom blade clamp oscillates as it should. Top blade clamp is spring loaded. Table tilts 45 degrees to each side. This is being sold as a project, may be missing more than just the motor.
...more

Bid Not Accepted!

Bid Accepted!

You've been outbid!

Sold for: USD 1.25

You've been outbid  to h****y! to YOU!

Placing your bid. please wait...

Black & Decker circular saw on Pippin linear guide assembly

Lot # 581      

Saw runs fine. Linear guide has 13" of travel and swivels 45 degrees to each side. Saw height is adjustable by a lead screw. Bring tools to remove from workbench.
...more

Bid Not Accepted!

Bid Accepted!

You've been outbid!

Sold for: USD 5.50

You've been outbid  to h****y! to YOU!

Placing your bid. please wait...

5 speed cast iron bench top drill press with 1/2" chuck, 4" vise, more

Lot # 580      

Machine shows very little use. Runs smoothly. Speeds range from 760 rpm to 3070 rpm. Adjustable depth stop. Keyed switch. Cast iron table tilts 45 degrees to each side and swivels. Cast iron vise is in good shape.
...more

Bid Not Accepted!

Bid Accepted!

You've been outbid!

Sold for: USD 120.00

You've been outbid  to b****w! to YOU!

Placing your bid. please wait...

Craftsman 10" tilting miter saw

Lot # 579      

Saw head tilts 45 degrees. Table swivels 47 degrees each direction. Shows little to no use. Bottom of guard is cracked, looks like it encountered the blade. Tested, runs. Comes with 10" 24 tooth carbide blade.
...more

Bid Not Accepted!

Bid Accepted!

You've been outbid!

Sold for: USD 95.00

You've been outbid  to a****a! to YOU!

Placing your bid. please wait...

Search Catalog :
Sort By :
Go to Lot :
Go to Page :
Per Page :
Pg : 1 of 20

1.178.0.1774.cf7307d.25.196