CEI ENTERPRISES HEATER, HOT OIL, STATIONARY CEI-1000: Consisting of but not necessarily limited to: Burner Unit. 2- Pass with Vertical Exhaust Stack, Mounted, Skidded, Forced Air Burner, Natural Gas Fired, MAXION and FIRE EYE Safety Controls and Valves, Pressure Regulators, Pedestal Mounted Electrical and Instrumentation Panel. 3- CIRCULATION AND ASPHALT METERING PUMPS: Centrifugal, 2 in. x 2-1/2 in. (est.) each independently powered by Electric Motor. FILLER, CARTRIDGE TYPE, Stainless Steel, Vertical, 10 in. dia. x 36 in. high (est.). PIPING MANIFOLD, Consisting of but not necessarily limited to: 4 in. OD (est.) Flanged Piping, with 3- (approx.) 4 in. , 6- (approx.) 2-1/2 in. and 6- (approx.) 1 in. Gate Valves; Most of the Manifold Piping has 2-1/2 in (approx.) thick Insulation with Exterior Metal Sheathing. TANK, ASPHALT CALIBRATION: 880 gal. (approx.) capacity, Vertical, Welded Carbon Steel, 5 ft. dia. x 6 ft. tall (est.) mounted on 3- Load Cells and on a 50 in. high (est.) 3- Leg Steel Platform with Fill and Discharge Piping, 4 in. dia. and smaller; 2- Gate Valves; 3- 2 in. OD (est.) Hoses having Stainless Steel Braided Flexible Exterior Armor. ELECTRICAL POWER DISTRIBUTION AND CONTROL PANEL: Consisting of but not necessarily limited to: 1- GENERAL ELECTRIC Cat. NO. AEF3424MBX, A Series® Panel Board, No. AXB7P2, 400 amps, 480Y/277 volts, with 3- GENERAL ELECTRIC Service Disconnect Panels, each with Control Switches and Status Lights. TANK, USED OIL, 2,100 gal. (approx.) capacity, Vertical, 6 ft. dia. x 10 ft. tall (est.) Welded Steel Construction, Flat Top and Bottom, Uninsulated, having Bottom mounted Agitator powered by Electric Motor with Electrical Power Control Box. TANK, USED OIL, 7,500 gal. (approx.) capacity, Horizontal, 8 ft. dia. x 20 ft. long (est.) Welded Carbon Steel Construction, with 3 in. OD (est.) Top Filling and Bottom Discharge Manifold, mounted on 2- I-Beam Skid with Welded Steps Climbing Ladder, Uninsulated, with Equipment Porch having a Transfer Pump powered by Electric Motor, 1- 12 in. dia. x 24 in. high Filter Unit. Co. No. 2 and 7. TANK, USED OIL, 7,500 gal. (approx.) capacity, Horizontal, 8 ft. dia. x 20 ft. long (est.) Welded Carbon Steel Construction, with 3 in. OD (est.) Top Filling and Bottom Discharge Manifold, mounted on 2- Beam Channel Steel Base with Climbing Ladder, Uninsulated. Co. No. 1 and 8. TANK, USED OIL, 11,200 gal. (approx.) capacity, Horizontal, 8 ft. dia. x 30 ft. long (est.) Welded Carbon Steel Construction with 3 in. OD (est.) Top Filling and Bottom Discharge Manifold, mounted on a Steel Base, Insulated having Rolled, Corrugated Metal, Exterior Skin, Co. No. 5. TANK, USED OIL, 11,700 gal. (approx.) capacity, Vertical, 10 ft. dia. x 20 ft. tall (approx.) having 4 in OD (est.) Midpoint Fill Line, Insulated with Rolled Corrugation Metal Exterior Cladding, Welded Carbon Steel. Co. No. 1. TANK, USED OIL, 42,000 gal. (approx.) capacity, Vertical 20 ft. dia. x 18 ft. tall (approx.) having Cone Top, Insulated with Rolled Corrugation Metal Exterior Cladding, Welded Carbon Steel. Co. No. 6 and 2. TANK, USED OIL, 46,000 gal. (approx.) capacity, Vertical, 14 ft. dia. x 40 ft. tall with Flat Top and Bottom, Insulated with Aluminum Exterior Metal Cladding. Co. No. 4. TANK, USED OIL, 25,000 (approx.) capacity, Vertical, 12 ft. dia. x 30 ft. tall with Flat Top and Bottom, with Full Length Exterior mounted Float controlled Fluid Level Gauge graduated in 1 in. Increments, Insulated with Aluminum and Metal Cladding, Placard 580/28, Co. No. T325/5 150 Pen. TANK, USED OIL, 25,000 gal. (approx.) capacity, Vertical, 12 ft. dia. x 30 ft. tall with Flat Top and Bottom, with Full Length Exterior mounted Float controlled Fluid Level Gauge graduated in 1 in. Increments, Insulated with Aluminum and Metal Cladding, Placard 580/28, Co. No. T305/5 EA-1. TANK, USED OIL, 25,000 gal. (approx.) capacity, Vertical, 12 ft. dia. x 30 ft. tall with Flat Top and Bottom, with Full Length Exterior mounted Float controlled Fluid Level Gauge graduated in 1 in. Increments, Insulated with Aluminum and Metal Cladding, Placard 580/28, No Co. Number. HAYWARD STRAINER, NO. 72 ST-272-0800R-3R WCB, Having 8 in. dia. Flanged Inlet and Outlet Ports. VIKING PUMP BASKET STRAINER Lid Ease® 11872448: Having 4 in. dia. (est.) Flanged Inlet and Outlet. VIKING PUMP VANE TYPE PUMP: 4 in. dia., powered by WESTINGHOUSE 25 hp Electric Motor with Piping and Valve Manifold and with 1- 4 in. dia. x 20 ft. long (est.) Hose having a 25 ft. high (est.) Gantry Crane with Manually Powered Wire Rope Hoist.
...more